[youtube v="pywrCioTz7o" maxwidth="420px" center="no"]
Wegener Remote
Before you can use the remote to control your TV's Power and Volume, you'll need to program it for your TV brand.
1. Determine the brand of your TV (i.e. Sony, Samsung, etc).
2. Find the codes for your TV brand in the User's Guide.
3. Simultaneously press and hold down the TV and OK buttons on the remote until the TV button stays lit.
4. Use the number keys to enter the first 3‐digit brand code listed for your TV manufacturer. Your TV will turn off when the correct code has been entered.
You can verify you have the correct code by pushing the Power button. The TV should turn on or off. If the TV button flashes rapidly for a second and then stays lit, it means the remote doesn't recognize the brand code you entered. Enter the next code listed for this brand, and continue down the list until one works.
5. Verify that the POWER and VOL buttons work.
[youtube v="w7xBxf03k8w" maxwidth="420px" center="no"]
Amino 530 Remote
Before you can use the remote to control your TV's Power and Volume, you'll need to program it for your TV brand.
1. Identify the make of the TV (i.e. Sony, Samsung, etc).
2. Find the codes for your TV brand in the User's Guide.
3. Press the TV Mode button and hold for 2.5 seconds. The TV button will blink twice.
4. Continue to hold down the TV mode button for another 2.5 seconds. The TV button will blink twice again.
5. Release TV mode button.
6. Enter the 3-digit TV brand code from the list in this manual.
At each key press the mode button will blink. If the TV brand code is accepted, the TV button will flash twice and go out when the 3rd digit is entered. If the TV brand code is not accepted, the TV button will remain illuminated for 2.5 seconds and then go out. The remote will not have been programmed and the process will have to be repeated from the start.
During the programming steps if no button is pressed after 10 seconds, the TV button light will go out, the remote will not have been programmed, and the process will have to be repeated from the start. If during programming the TV button is pressed, the TV button will light for 2.5 seconds and go out. The remote will not have been programmed and the process will have to be repeated from the start.
[youtube v="QlHUr5U2JvQ" maxwidth="420px" center="no"]
Amino White Remote
Before you can use the remote to control your TV's Power and Volume, you'll need to program it for your TV brand.
1. Determine the brand of your TV (i.e. Sony, Samsung, etc.).
2. Find the codes for your TV brand in the User's Guide.
3. Simultaneously press and hold the TV and OK buttons on the remote.
4. After approximately 2 seconds, the TV button will light. Release the TV and OK buttons. The TV button should remain lit.
5. Now enter the 3-digit brand code according to the make of the TV that is being controlled.
As each of the digits are entered, the TV button will briefly flash off and on again. When the third digit has been entered, the TV button will go out. If a TV brand code has been entered that the remote does not recognize, the TV button will flash rapidly for a second and remain illuminated. If this happens, re-enter the correct TV brand code.
Verify that the remote control works with the TV. Most TV makes have more than one brand code listed in the brand code table. If this is the case try all brand codes that are listed for that make until a suitable match is found.If no brand code is listed for the TV, try brand codes for Philips and NEC TV's.
[youtube v="eiLsxYFQZqk" maxwidth="420px" center="no"]
Millenium 4 Remote
Before you can use the remote to control your TV's Power and Volume, you'll need to program it for your TV brand.
1. Determine the brand of your TV (i.e. Sony, Samsung, etc.).
2. Find the codes for your TV brand in the User's Guide.
3. PRESS and RELEASE the TV button.
4. PRESS and HOLD the SETUP button until the red LED for the selected device flashes twice, then RELEASE.
5. ENTER the 4 digit code for your TV brand. You should receive 2 quick flashes on the LED for the selected device after entering your code.
6. PRESS the POWER button to test the code.
